Safety management

How to do a job hazard analysis (JHA), step by step

How to do a job hazard analysis: pick the jobs that matter, break them into steps, find the hazards, choose controls with the hierarchy and keep it current.

Updated 8 minute readBy the EHS Nation team

A job hazard analysis is one of the most useful tools in safety, and one of the most often done badly: copied from a template, signed once and never read again. Done well, it's how a crew agrees what can go wrong on a job and what they'll do about it.

What a JHA is

A job hazard analysis (JHA), also called a job safety analysis (JSA), looks at one job at a time. You break the job into its steps, find the hazards in each step, and decide the controls for each hazard. The result is a short document the crew can use before and during the work.

OSHA's free publication Job Hazard Analysis (OSHA 3071) describes the method in detail.

1. Pick the job

You can't analyze everything at once. Start with the jobs most likely to hurt someone badly:

  • Jobs that have caused injuries, illnesses or near misses
  • Jobs where a mistake could kill or seriously injure someone, even if it hasn't happened yet
  • New jobs, and jobs where the process, equipment or materials have changed
  • Jobs done rarely, such as shutdowns and non-routine maintenance, where people have less practice
  • Jobs complex enough to need written instructions

2. Break the job into steps

Watch the job being done, and talk to the people who do it. Write each step as an action, in the order it happens: "Lock out the conveyor", not "Lockout".

  • Not too broad. "Change the blade" hides the hazards. Split it until each step is one action.
  • Not too detailed. If the list runs to dozens of steps, you're writing a procedure. Group small actions together.
  • Include the steps around the job: getting tools and materials, setting up, cleaning up and restarting.

3. Find the hazards in each step

For every step, ask:

  • What can go wrong?
  • What would the consequences be, and how bad could they be?
  • How could it happen? What would have to fail?
  • What makes it more likely: time pressure, poor lighting, weather, shift work?

Think about energy (moving parts, electricity, pressure, heat, stored energy), gravity (falls and falling objects), chemicals, noise, ergonomics, vehicles and people working nearby.

4. Choose controls with the hierarchy

Work down the hierarchy of controls, and only move to the next level when the one above isn't practical. ISO 45001 8.1.2

  1. Eliminate the hazard: design it out, or don't do the task at all.
  2. Substitute something less hazardous: a safer chemical, a lighter load.
  3. Engineering controls that separate people from the hazard: guards, interlocks, ventilation.
  4. Administrative controls that change how people work: procedures, permits, training, signs, job rotation.
  5. Personal protective equipment, as the last line of defense.

If PPE is part of the answer, remember OSHA's general industry rules require a hazard assessment for PPE, certified in writing. 1910.132(d)

Write controls people can act on. "Be careful" isn't a control. "Stand outside the swing radius and use a tag line" is.

5. Use it, and keep it current

  • Review it with the crew before the job, especially for non-routine work.
  • Check it in the field. Watch the job and see whether the controls are really in place.
  • Update it after any incident or near miss on the job, and whenever the job, equipment, materials or people change.
  • Review it on a schedule, such as yearly, so it still matches how the work is done.

An example

Part of a JHA for clearing a jam on a packaging conveyor:

StepHazardControls
1. Stop the conveyor and lock it outConveyor restarts while hands are in itFollow the machine's lockout procedure, apply a personal lock, and try the start button to verify zero energy
2. Remove the guardCuts from sharp edges; dropping the guard on feetCut-resistant gloves; two people for the large guard; safety shoes
3. Clear the jammed productPinch points; stored tension in the beltUse the jam hook, not hands; release belt tension before pulling product
4. Refit the guard and restartSomeone still in the danger zoneCheck everyone is clear, refit and test the guard interlock, remove locks, announce the restart

Questions

Frequently asked questions

What's the difference between a JHA and a JSA?

Usually nothing. Job hazard analysis (JHA) and job safety analysis (JSA) are two names for the same method: break a job into steps, find the hazards in each step, and set controls for each hazard.

Is a job hazard analysis required by OSHA?

OSHA has no general rule requiring a document called a JHA. But several standards require you to assess hazards, for example 29 CFR 1910.132(d), which requires a workplace hazard assessment for PPE with a written certification. A JHA is a common way to meet those duties.

How often should a JHA be reviewed?

Whenever the job, equipment, materials or people change, after any incident or near miss on the job, and at a regular interval such as once a year, so it still matches how the work is really done.

Who should do a job hazard analysis?

The people who do the job, with a supervisor and someone who knows the hazards. Workers know the shortcuts and the steps that never make it into the procedure.

Regulations and standards

The rules behind it

Summaries on this site are in our own words. Follow a link to read the official text. EHS Nation helps you keep records and run your program; it doesn't replace your own judgment or legal advice.

Next step

See EHS Nation with your own sites and forms.

Book a demo and we'll walk through the platform with your locations, your forms and your questions. No slides, no pressure.

  • About 30 minutes
  • Your sites and forms
  • No slides